Facade Build-Up and Window Shroud Sizing: Getting the Detail Right

Centurion window shroud custom made by Alumac.

A window shroud or sun hood detailed on a 12mm rendered wall will look wrong on a 50mm battened and clad facade. This sounds obvious, but it’s one of the most common sources of shroud specification errors on residential and multi-residential projects, the shroud dimensions are confirmed before the facade build-up is properly resolved, and by the time the discrepancy is noticed, fabrication is already underway.

This article is for architects and specifiers. It covers the relationship between facade build-up and shroud sizing, what needs to be resolved before dimensions are confirmed, and the details that are most commonly missed.

Why Facade Build-Up Matters More Than the Window Size

When specifying a window shroud, the instinct is to start with the window: width, height, desired projection. That’s a reasonable starting point. But the window size alone doesn’t determine what the shroud looks like on the completed facade.

What actually determines the visual outcome is the relationship between four things:

  1. The window frame position: Where does the window frame sit relative to the finished face of the wall? Is it flush, recessed, or projected?
  2. The facade build-up thickness: How much material is between the structural substrate and the finished face of the wall? On a rendered masonry wall this might be 15mm. On a battened and clad system it could be 50–100mm or more.
  3. The fixing substrate: Where is the shroud actually fixed, to the structural substrate behind the cladding, or to the face of the cladding? This determines the bracket or flange design.
  4. The reveal depth: The reveal is the visible return between the face of the cladding and the window frame. The shroud needs to relate correctly to this detail, covering the right amount of reveal without cutting across it awkwardly.

Get all four of these resolved and the shroud dimensions follow logically. Leave any of them undefined and you’re guessing.

The Most Common Specification Errors

Ordering from the structural opening, not the finished opening: The structural rough opening is always larger than the finished window size. The shroud is sized to the finished window frame, not the framing. Using the wrong reference point produces a shroud that either covers part of the window glass or floats visibly away from the frame.

Not accounting for cladding thickness in the projection depth: A shroud that projects 150mm from the face of the structural wall projects only 100mm from the face of 50mm cladding. If the projection depth has been specified for solar control purposes, BASIX or passive solar, the effective projection is what matters, not the nominal depth from the fixings.

Detailing on a different facade system to what gets built: It’s not uncommon for a project to specify a rendered facade at DA stage and switch to a battened cladding system during documentation. The shroud detail changes significantly between these two systems. If the specification isn’t updated, the fabrication drawings won’t reflect the actual facade.

Ignoring the junction detail at the wall: The point where the shroud meets the wall needs a flashing or sealant detail to prevent water entry. On a rendered wall, this is usually a sealant joint. On a cladded facade, there may be a need for a flashing that integrates with the waterproofing layer behind the cladding. This detail needs to be on the drawing, not resolved on site by the installer.

Working Through the Dimensions

Here’s a practical sequence for getting shroud dimensions right.

Step 1: Confirm the facade build-up. Get the full layer-by-layer thickness of the facade system confirmed, structure, waterproofing, insulation (if external), battens, cladding, finish. This is your reference for all subsequent calculations.

Step 2: Confirm window frame position. Note whether the frame is flush with the face of the cladding, recessed behind it, or projected. The shroud needs to clear the frame and sit at the correct relationship to the reveal.

Step 3: Determine the fixing substrate and method. Is the shroud fixing into masonry, concrete, framing or a dedicated fixing rail? This affects the bracket or flange design and may affect the minimum projection depth available.

Step 4: Calculate the effective projection. If the shroud projection is specified for shading performance, calculate the projection from the finished face of the facade, not from the fixing point. These are different numbers on a thick cladding system.

Step 5: Confirm the junction and waterproofing detail. Draw the junction between the shroud and the wall, including any flashing, sealant joint or backing rod. This should be on the construction documentation, not left to the discretion of the installer.

Step 6: Cross-check with the fabricator. Before dimensions are confirmed and fabrication begins, the fabricator should review the drawings and flag any dimensional issues. At Alumac, we regularly pick up discrepancies at this stage that would have created problems on site.

Consistency on Multi-Window Projects

On projects with many windows, apartments, townhouses, commercial buildings, consistency is everything. Thirty shrouds that are each 2–3mm out of position, or that sit at slightly different depths relative to the finished wall, read as sloppiness on an otherwise carefully designed facade.

Achieving consistency requires:

  • A single, fully resolved facade build-up detail that applies across all affected elevations
  • A clear and complete fabrication drawing with all dimensions from a consistent datum
  • A fixing sequence that the installer follows precisely for every opening
  • A single fabricator handling all units in the same powder coat batch

Splitting the order between fabricators, or fabricating in multiple batches without colour matching, is a reliable way to produce a facade that looks wrong even if every individual unit is technically correct.

When to Brief the Fabricator

The best time to involve a fabricator in the detail is during design development, before the facade system is locked in and before construction documentation begins. This isn’t about getting a quote early, it’s about having a technical conversation while there’s still flexibility to refine the detail.

Alumac works with architects and specifiers at this stage on a regular basis. If you’re resolving a facade detail and want to talk through how the shroud specification interacts with your cladding system, get in touch. We can provide fabrication drawings, projection depth data and fixing details to support your construction documentation.

Scroll to Top